It involves many steps - developing a design, transfering the design to the wood blocks, carving the blocks, choosing paper, printing the blocks - and each step introduces many variables so there are many challenges to this art form. The process, however, is far from simple. Japanese woodblock prints are known especially for their intense use of color and for the fact that the pigments are water-based rather than oil-based.Īll that is needed to produce a Japanese style woodblock print is wood, water, pigment, paper, a few carving tools, some brushes and something to rub the paper with - simple materials that anyone can easily acquire and get started with right away. After a time colors began to be added by hand and then, as woodblock printing became the primary form of commercial printing in Japan, printers began to carve blocks for each color. Woodblock printing was brought to Japan in the 8th century by Buddhists from China and was first used to reproduce religious texts. While I have great respect for multidisciplined artist-producers, my rout is that of the craftsperson.Moku hanga is the Japanese term for woodblock print ( moku means wood and hanga means print). An artist didn't print and a printer didn't carve. Today many printmakers play multiple roles, but in the traditional system, these four roles were clearly demarcated. The final person to mention in these process would be the published who organises commissions and pays for the crafts people to produce the print. a registration system(kento) was carved into each block by the carver consisting of a L-shaped notch (kagi) in the bottom right-hand corner and a flat line somewhere along the bottom edge (hikitsuke.) before printing the paper is wetted and must remain at a constant moisture level through the process to avoid swelling or shrinking as this would cause misregistration in the final print. depending on the printable area or delecy of carving for each block. The printer then rub pigments on the blocks one after another and press the paper into them using a range of bar ens fromcourse to every fine. once this process is done the work of the carver is done for the time being and the blocks are then sent off to the next person in the chain, the printer. then in the same manner as the key block was produced this will then be glued t the block and carving will continue. Several impressions are taken from the block and colours are worked out for the print by marking off wanted areas. Sumi ink is then spread over the block (usually using a horse hair brush called a marubake -round brush) and impressions are taken by placing paper on top and rubbing the back of it with a rubbing tool called a baren. this is called the Omohan or Daiban in (English key block.) After washing the glue and paper off the block, it is then ready for printing. The lines are then cut on both sis ides and the waste wood cleared in between leaving behind a raised design on the surface of the block. (a touch of camelia may be used to produce even more transparency, but this should be done just before carving as the oil may cause the paper to pull up from the block after some time.) Once the design is pasted to the block and back of the paper removed by rubbing with a bit of water to remove layers of paper to reveal the design. This gives us much more fidelity to the original brushstrokes of the artist and is standard practice today. Today the job of creating a hanshita can be done by digitally tracing and then printing in the case of reproductions or simply by printing a design on to paper of the carvers (almost always gampi). This will then be turned into a hanshita (a lined design ready for pasting down on to a woodblock for carving usually produced on gampi.) Whether produced by the artist himself or more often by the workshop that will produce the print, a piece of very thin paper is placed over the design and carefully traced, filling in any recurring details to the artists' instructions or cleaning up messy lines. The process traditionally beggins with an artist drawing. Today there are very few masters of this craft. However, in the Edo era, the art of multicoloured printing was mastered and became widely available to the general public. Originally, prints were produced by carving the key outlines and painting on top to create full-colour images. In Japanese "moku" means wood and "hanga" means print, therefore mokuhanga is the Japanese term for woodblock print.Ĭoming originally from China, woodblock printing was mastered in Japan.
0 Comments
Leave a Reply. |